Changzhou FRP Shipyard Co., Ltd. boat

+86-12345678910
Language

中文版

English

Confirm
glass steel

Blog

The following points should be noted for the spraying construction of aluminum alloy boats.

The following points should be noted for the spraying construction of aluminum alloy boats.

When spraying aluminum alloy boats, the following points should be noted: Before starting the coating work, the operator should check the spray gun and adjust it to produce the ideal spray pattern.

26

2022

/

07

铝合金艇喷涂施工要注意以下要领

铝合金艇喷涂施工要注意以下要领

　　铝合金艇喷涂施工要注意以下要领：开始施工涂料前，施工者应检查喷枪，并调节喷枪以产生理想扇面。

26

2022

/

07

Environmental requirements and spraying construction essentials for aluminum alloy boat coating

Environmental requirements and spraying construction essentials for aluminum alloy boat coating

Environmental requirements for aluminum alloy ship coating process: During all construction stages of this process, the temperature and humidity of the construction environment must be monitored. The coating environment temperature should be between 5-35℃, with relative humidity below 85%, and the substrate surface temperature should be at least 3℃ above the dew point. Temperature and humidity should be measured near the substrate. If the substrate temperature exceeds 40℃, construction is not recommended. Construction must strictly follow the product's environmental requirements. There should be no dust around the hull, and construction can be enclosed with good ventilation conditions.

12

2022

/

07

铝合金船涂装环境要求和喷涂施工要领

铝合金船涂装环境要求和喷涂施工要领

铝合金船涂装工艺的环境要求:在此过程的所有施工环节都要对施工环境的温度和湿度进行监控。涂层环境温度为5-35℃，相对湿度低于85%，基底表面温度高于露点3℃。温度和湿度应在基底附近测量。基底温度高于40℃，不建议施工。严格按照产品施工环境的要求进行施工。船体周围没有灰尘，可以封闭施工，通风条件好。

12

2022

/

07

Precautions for Spraying Aluminum Alloy Boats

Precautions for Spraying Aluminum Alloy Boats

The aluminum alloy boat uses methods such as surface painting for protection or installing anti-corrosion zinc blocks to avoid the attachment of shellfish, algae, and other objects that could reduce the boat's speed or accelerate the aging of the aluminum alloy.

29

2022

/

06

铝合金艇喷涂施工注意事项

铝合金艇喷涂施工注意事项

　　铝合金艇为避免船底附着贝类、藻类及其他物体造成船艇航速降低或者加速铝合金老化而在表面进行油漆防护或安装防腐锌块的方法。

29

2022

/

06

Corrosion protection process for the surface of aluminum alloy official boats

Corrosion protection process for the surface of aluminum alloy official boats

Aluminum alloy公务船 employs surface painting protection or the installation of anti-corrosion zinc blocks to prevent the attachment of shellfish, algae, and other objects to the hull, which can reduce the vessel's speed or accelerate the aging of the aluminum alloy.

10

2022

/

06

铝合金公务船表面防腐工艺

铝合金公务船表面防腐工艺

　　铝合金公务船为避免船底附着贝类、藻类及其他物体造成船艇航速降低或者加速铝合金老化而在表面进行油漆防护或安装防腐锌块的方法。

10

2022

/

06

< 1...293031...40 >